Airsoft Gun Shot Full Auto and Stopped Working When Connecting the Battery

Problem – SOLUTION

Gun does non fire.

a, Check to meet if the selector lever is in the correct position.
b, Cheque to make certain the battery is plugged in securely.
c, Bank check to brand sure the battery is charged, or try another battery that is fully charged.
d, Cheque to brand sure battery is the recommended voltage as specified in the production manual.
e, Check the Fuse. As these can get blown if battery voltage is to high.

Gun fires but no BBs come out.

a, Check to encounter if the magazine is fully loaded.
b, Bank check to see if the mag is fully wound.
c, Check to see if the magazine is fully seated into the receiver. It should click when fully seated.
d, Remove the magazine and check if the mag is jammed or gun barrel is jammed.

BB jams in butt.

a, Remove the magazine, use the bevelled end of the cleaning rod to push the jammed BB back of the BB loading nozzle. (See Clearing a BB Jam)
b, Dry fire with no Bulletin board system to make certain gun is firing properly. Reinsert loaded magazine and test fire.
c, Employ only new, high quality BBs of 0.20g weight or heavier. Practice not use 0.12g BBs.

Motor is heard whining, but gun does not fire.

a, Adjust the motor top by using an advisable wrench on the spiral on the bottom of the pistol grip. Tighten screw until the gun fires smoothly.

Motor is heard grinding and the gun fires slowly.

a, Adjust the motor superlative past backing out the grip screw until the gun fires smoothly.

Gun clicks when the trigger is pulled.

a, Charge your battery and try once more.
b, Attempt some other fully charged battery.
c, Check to see if your motor grip screw is too far in.

Bbs practise not fly straight.

a, Adjust hop-upwards as detailed in the product manual.

Bulletin board system do not fly very far.

a, Clean your inner barrel and add a minimal of silicone lubricant into the BB loading nozzle. (See Cleaning the Inner Butt)

Motor grip is getting hot.

a, This tin can exist mutual and a little heat with heavy usage can happen, but is all-time to disconnect the battery and set up the gun down for a minutes to be on the safe side.

Battery is smoking.

a, Immediately stop shooting.
b, Disconnect the battery and set information technology in a non-flammable expanse if possible.
c, Consult with your battery instructions or an authorized airsoft gunsmith.

General Tips

Charging the battery.

About quality airsoft guns do not include a bombardment and may demand to be acquired separately. When you lot receive a battery it will be empty or almost empty. Using the gun with a tuckered battery can cause damage to its jump, gear or motor. You should always charge your bombardment completely before you use your detail especially when it is the first time. If the gun'south rate of fire and trigger response decreases you know information technology's time to stop and recharge the battery. And once more avoid using the airsoft gun with a low battery as it tin can go out the AEG with a jam or compressed spring (See Compressed Spring)
For Lipo batteries please be extra conscientious every bit there are extra risks for these batteries. Have a safe identify to charge then with zilch flammable around them. Exist enlightened of generally how long it should take to charge and wait for them. Eg: don't fall asleep or get out your home while charging lipo's. If a Lipo battery goes puffy a chemical reaction has begun and can't be revised, delight remove it to exist disposed in an appropriate safety battery disposal.

Setting the Hop-up.

A common mistake a new Airsoft tin can brand is forgetting to set the hop-up or to brand matters worse, plough it upwards to total. It puts spin on the BB helping it control the trajectory. The BB drops quickly in case of a little hop-upwardly. Besides much hop-up the BB will arc up and could even jam a bb in the hop unit of measurement. To have a nice flat trajectory the Hop-up mechanism is used and adjusted in modest increments to observe the correct hop position. It is best advised that you follow the manufacturer'south guide or experienced airsofter for best pedagogy on this matter.

General Cleaning.

It is advised that you don't use water to wash the gun, due to potential rust and electrical bug, or if you do a damp cloth at a minimal. Best choice you can utilise a silicon lubricant to wash it and help forbid rust. For finer detail use Q-tips, and get all the pocket-sized little cracks and crevices. If its metal you're cleaning you might want to spray some silicone oil on it and rub it off with paper towel really practiced. Silicone Oil is a good mode to preclude rust from actualization or spreading. Although don't use besides much lube or your gun volition go a dust magnet. So once again a gentle rub downwardly with a silicone dampen fabric is best.

Cleaning the Inner Butt.

As airsoft internals systems are completely different from real steel systems, so is the inner barrel cleaning is required a lot less then for existent guns. Grit and dirt can notwithstanding build upward if it'south not removed and cleaned every half-dozen months so from a regular used airsoft gun.
To make clean the barrel properly, take a cleaning rod, with a small tissue patch and spray minor amounts of silicone spray to the patch. Turn your hop upward completely off before you insert the cleaning rod.
Inside of the barrel needs to exist wiped down in a back and forth motility. Remove the tissue patch from your cleaning rod. Use a new, dry patch inside the barrel.
You may take to repeat the process to articulate out the remaining residue until the tissue comes out near make clean from dirt from within the barrel.

Clearing a BB Jam

NEVER look downwards the end of butt for whatever reason!
1. Brand sure the airsoft gun is "ON Rubber" and pointed in a SAFE Direction.
ii. Remove mag.
3. Insert the tapered cease of the cleaning rod into the barrel, with the angle toward the magazine connects to the Hop-upward
4. CAREFULLY and slowly apply more than pressure level until yous push the BB out of the breech.
Reinstall the mag and examination gun.

Semi but Jam.

A trouble that new users may face is sometime shooting in semi just the gearbox gets stuck. This problem is very easy to correct by just putting your gun to auto and fire a few rounds to gratuitous up the gearbox, and and so switch back to semi if required. Can also occur with a low bombardment, and a fully charge battery with a full machine flare-up will correct this.

Compressed Spring.

A compressed spring tin occur naturally in the normally total auto cycle of an AEG and happens when the piston is positioned fully at the rear of the gearbox. This in itself is not an result.
But a trouble of compressed spring that can cause impairment / power loss, once information technology's in this position and the model is put in storage for a long period of fourth dimension.
The simple solution to this problem is every time before yous pack yous gun abroad is to burn the model in single fire mode starting time and this will release whatever compressed spring.
If you model has suffered from a compressed spring one time removed from storage, the leap will demand to be replaced to regain the lost power.

AEG Storage.

Always remove batteries from AEG and belch them (non-Lipo) for long storage.
All hopup's should be turned off and BB's removed from mag to decompress springs.
A footling silicone oil spray on moving parts and rubbers before and after storage tin can also help as well.

General GBB Maintenance.

With regular usage or removing from storage, it is important to remove the slide to spray the slide grooves and around the loading nozzle in the rear of the slide with silicon oil. The loading nozzle should exist able to spring forwards and backwards with ease. A barrel clean every 5000 rounds can marginally help with accuracy.
Besides note: GBB pistols do non perform well nether 10°C. You will experience gas rushing out of the barrel, reduced ability and cycling problems. Optimum performance is achieved in temperatures of 18°C and above.
DO Not use any petroleum based lubricant like WD-40 as this corrodes whatever plastic or safe inside the pistol.

GBB Mag Loading.

To load a GBB mag with gas, the bottle is held at a 45 degree angle above the mag infill valve and pushed together. Some gas may escape, but this is not a problem.
If y'all try this horizontally / sideways, the mag won't load with gas properly and simply be half filled at best.
For a M1911-sized magazine, approximately 5-6 seconds fills the mag. For larger Beretta/Glock/Sig magazines, 6-10 seconds fills the magazine fully.
Input bb's into the mag as per instructions in the owner's transmission.
To insert the mag in the airsoft gun, lock the slide to the rear (empty position) earlier inserting the magazine. Release the slide and you're ready to shoot.

Leaking Gas Mags.

Gas mags leaking is inevitable. What matters is y'all know how to maintain them well so the leak less or never if well maintained. Always keep your o-rings damp with silicone oil spray and keep valves tightened if they get loose. DO NOT drop your GBB mags, no matter how cool you recall information technology is! They are non designed to exist dropped!
If gas mags are dropped to many times, the structure can get damaged and can even explode.
The design of most mags are simple, in-valve, out-valve, and o-rings between ii halves of a body, with spring and pusher for bb's.
So sealing issues can be only aided with silicone oil and more with Teflon tape or even thread lock gum in the metal on metal areas if need be. Only please brand certain all gas is removed from the gas mag before any form of maintenance or opening of the mags is attempted, as they tin explode if y'all endeavor.
To release the gas press the knocker valve (outward valve) on the dorsum of the magazine to expel gas from the pinnacle of the magazine, merely signal the vent in a prophylactic direction first.

GBB Mag Storage.

Never leave your Gas magazines filled with gas in storage.
The full pressure will deform the o-rings releasing the gas and o-rings will demand to exist replaced.
But it is recommended simply a acquit minimal of gas in you mags is to continue a proficient seal in storage. And a fiddling squirt of silicone oil on valves won't hurt ether.

Classic Ground forces Shop , articles all metallic MP5'south and accessories. Based in Hong Kong. Includes product summary and contact information.